What to do when your bill is based on an estimate read.
Sometimes your bill needs to be estimated rather than based on actual reads from your meter. This is shown in one of two ways on your bill.
An estimated read (E) happens when your meter provider doesn’t provide us with an actual read of your meter, so the consumption shown on your bill is an estimate based off your past usage patterns. This is what you’ll see on your bill if you’ve received an estimated read –
A substitute read (S) means your consumption data has been provided by your meter provider in the event of them being unable to read your meter. This is what you’ll see on your bill if you’ve received a substitute read –
If you’re concerned about the reading, you can request an adjusted bill based on your own meter reading estimate by following the steps below.
Meter readings and reading meters.
How to send us your own meter readings.
Reading your own gas and electricity is not as difficult as you may think. Below are some instructions on how to do it. We’ve also included information on how you can provide meter reading information to us.
If you want us to provide an adjusted bill estimate based on your own reading, any meter reading information you provide to us need to be received by us before the due date of your bill or it may be rejected.
Please note that we will be unable to accept meter reading from Victorian customers with digital meters (also referred to as smart meters).
How to provide your meter reading information to us.
You must send us a photo
Take a very clear photograph of your electricity or gas meter and be sure to include any relevant serial or reference numbers that are on the meter in the image.
If you have multiple meters on site please ensure that each photograph clearly shows the serial number for each meter.
Important tips on taking a clear photo.
The photo must not be blurred (e.g. it must be in focus) and must also be taken with a sufficient amount of light. Make sure there is no reflection in your photo. Reflections can come from lights, the sun or even the flash on your camera. If this happens when you take your photo, try moving the camera to a different angle or shade the meter from the sun or the light(s) causing the reflection and take the photo again.
Email the photo to us at email@example.com and make sure you include your account number and if possible, your NMI and/or MIRN. You can find these on your most recent bill from us. The ‘NMI’ (which stands for National Metering Identifier) applies to electricity meters only. The MIRN (which stands for Meter Installation Reference Number) applies to gas meters only.
If you would like to post the photo to us, you can do that too but please allow sufficient time to ensure that the photo to arrives at the address below before the due date of the relevant bill. But we’d prefer you email it so we can resolve your query faster.
P.O. Box 352
Flinders Lane VIC 8009
Then what happens?After you’ve provided your reading to us, we will be in touch soon after to inform you of the outcome. We’ll either confirm if the reading was accepted or if it has been rejected.
If your reading is accepted, you will receive an SMS confirming it. A revised bill (with a new due date) will then be issued and sent to you.
If your reading is rejected, we will write to you and advise why. The original bill amount will remain in place and need to be paid, but you will have an extra 14 business days to pay the bill.
What could cause a rejection?
Photos may be rejected if:
- we are unable to derive a complete and/or usable reading(s) of your consumption amounts from the image(s) you have provided. Some of the reasons a photo may be illegible could include not in focus, taken too far away from the meter, too dark to see the meter clearly or the picture of the meter doesn’t have the reading in the image;
- the reading on the meter is less than the last actual read we received from your meter provider; or
- your read estimate was received on or after the due date for payment of the relevant bill. If your meter reading information is rejected, we will let you know as soon as possible and include the specific reasons for our decision. You may:
- request that we review the relevant bill in accordance with our standard complaints and dispute resolution procedures which can be found here. You may, in some circumstances, incur costs from a third party so we recommend you contact us to discuss your options first.; or
- lodge a dispute with the energy ombudsman if you are not satisfied with our decision after you have followed the process set out here.
For more details, please see Momentum Energy’s Complaint and Dispute Policy.
How to read your meter.
First, you’ll need to know what type of meter you have so we’ve included some pictures below to help with this. There are typically three different types of electricity meters and three types of gas meters. We have some information below on how to get the reading off the different types of meters. Electricity readings are recorded as a kWh (Kilowatt Hour) and gas reading are recorded as a MJ (Megajoule).
Clock Dial Type
In this image, the meter reading is 35095.
How to read this type of meter.
- Stand straight in front of your meter so that you can view where the hands are pointing on each of the dials.
- Read what each dial says by going from left to right (ignoring any red dials) and always by reading the lowest number closest to each pointer. (For example, if the pointer is between the 1 and the 2, it will be 1. If the pointer is between the 8 and 9, it will be 8. The exception is 9 and 0 – it’s always 9 in this instance).
- Repeat this for every dial and make sure you go from left to right.
In this image, the meter reading is 065912.
How to read this type of meter.
- This will be displayed similar to a car’s odometer (the old style odometers before they became digital).
- Simply read the number displayed on the meter, from left to right.
Electricity Digital Meter (sometimes referred to as a Smart Meter)
In this image, the meter reading is 20419.
How to read this type of meter.
- Scroll through the different screen options by pressing the SELECT/Scroll button. (Some of these meters will have instructions on the front telling you which screen to look at).
- Record the meter reading for the different consumptions. This will always be ‘Peak’, and if applicable ‘Off Peak’ and/or ‘Solar’ export.